|
|
| Product Information | | | PermaFlex epoxy protective
coatings are all two-part, Co-reacted polymers with superior elastameric properties with product Advantages & Benefits
suitable on a variety of surfaces including metal, asphalt, modified bitumen smooth and granulated, polyurethane foam, vinyl,
PVC, stone, TPO and EPDM rubber. | *
| Provides long term protection
against weathering, abrasion, under creep and has superior resistance to UV oxidation | *
| Usually requires no maintenance; however, should damage occur, due to
construction or maintenance repair is easy, quick, and simple | *
| Excellent adhesion properties even to damp surfaces with adhesion of product to substrate | *
| Remains flexible through years of
harsh service | *
| Withstands
attack from most chemicals, traffic, and severe environments | *
| Retards the growth of algae, mildew, black mold or mussels | *
| Retains flexibility in sub-zero conditions | *
| Withstands ponding water and resists hail damage | *
| UL Approved - Class "A"
fire rating as a fire retardant coating | *
| Barrier to heat transfer reducing surface temperatures to within a few degrees of 'ambient' temperatures | *
| Sustainable roofing system that saves the
buyer the cost of removal and disposal of the existing roof | *
| High Emissivity decrease heat and lowers energy cost | *
| Meets V.O.C. emissions regulations | *
| Standard and custom colors available | *
| 10 year extendable warranty available for roofs. Warranties available
for other certified PermaFlex products. |
California Residents Note: These products
meet or exceed EPA requirements for VOC's (Volatile Organic Compounds) and contain NO harmful environmental
solvents. _________________________________ |
|
| PFX-100 Flexible Roof Coating
| | | PFX-100 is a flexible two-part epoxy designed to protect a variety of surfaces including rubber, concrete,
foam, plywood, and metal. PFX-100 in conjunction with Polylace or Fiberglass fabric is also suitable for coating petroleum-based
surfaces such as tar or rubber cement. It is especially suited to applications where surface movement may defeat the protection
of a rigid coating. | Application Areas
PFX-100 is excellent for waterproofing EPDM, built-up, single ply,
foam, and metal roofs. It is also suitable for walkways, walls, sumps, and parking garages. The flexibility retained by PFX-100
allows for surface movement caused by thermal shock to most structures. | Preparation
Surfaces
must be cleaned free of grease, oil, films, dust, or any other contaminants. Most roof surfaces should be pressure washed
to remove any barrier films. Metal must be free of mill scale, oils, rust, etc. Hard-finished concrete should be etched to
provide profile or "tooth" for optimal adhesion. These preparation procedures are in general guidelines. Consult PFX
Approved Applicators & Technicians for further details or special preparation procedures. Roofing specifications are also
available for various substrates. | Mixing
The mixing of parts A & B is very
important! PFX-100 has a mixing ratio of 4 parts "B" to 1 part "A". Use a power mixer to thoroughly
combine both parts. Mix for at least 1 minutes per gallon. Allow idle activation time for at least 30 minutes. Lacquer thinner
should only be added after the mixing process is complete. | Application
PFX-100 can be applied
by air-less spray equipment, brush, or roller at approximately 100-sq. ft. per gallon per coat. A two-coat application is
recommended to help insure complete protection. Surfaces subject to significant movement or other difficult conditions may
require heavier applications and the use of Fiberglass Mesh. All penetrations or transitions of surface materials should be
covered with the Fiberglass Mesh . Surface configuration, weather, or area surroundings may dictate application method. | | Dry Film Application Rate | | To yield dry film of: | Apply sq. ft. gallon | | 12 mls. | 100
sq. ft. | | 6 mls. | 200 sq. ft. | | DO NOT apply heavier than 10 mils per coat.
If more is needed, apply in multiple coats. Allow PFX-100 to become tack-free before applying additional coats or approximately
6 hrs. at 80ºF. |
| | Application Recommendations | | Metal surfaces: | 1
gal. / 100 sq. ft. | | Foam or
build-up roofing: | 1.5 gal. / 100 sq.
ft. | | Build-up roof after removal
of gravel: | 3 gal. / 100 sq. ft. | | Concrete: | 1.5 gal. / 100 sq. ft. | | |
| Thinning
Lacquer thinning is recommended for best results. Do not exceed more than 2 quart per 5 gallon. Thinning retards cure time
and extends pot life. | General
PFX-100 should be applied in well ventilated areas. Surfaces should
be free of foreign matter. DO NOT apply near open flame. | Clean Up
Application equipment should be cleaned immediately with lacquer thinner. Use Apple Cider Vinegar to clean hands and skin.
Do not allow coating to remain on tools! Once it sets and is cured, it is difficult to remove.
| Flammability
Flammable during application. ALWAYS HAVE
A FIRE EXTINGUISHER ON SITE FOR SAFETY. Will not support combustion
when cured. | | Packaging | | 1 1/4 gal. units | 14.5 lbs./gal | | 1. 1 gal. can full, containing base | part "B" | | 2. 1 qt. can full, containing activator | part "A" | | | | | 5 gal. units | 57.5
lbs./gal | | 1. 5 gal. pail containing
4 gallons of base | part "B" | | 2. 1 gal. can full, containing activator | part "A" | | |
| Color
PFX Standard Color (White) | Solid Contents
75% Solids | Mixing Ratio
4 parts "B" to 1 part "A" (4:1) | Salt-Fog Testing
(ASTM B-117)
500 hrs. - pass | | Water Vapor Transmission (ASTM E-96) | | Permeance (expressed
in perms) - .749 | | Tensile Strength (ASTM D-638) - 1393 psi | | Adhesion: 210 lbs./sq.
in. | | Curing
Time | | Pot Life: | 6 to 8 hrs. at 80ºF | | Drying Time: | 12 hrs. at 80ºF | | Complete: | 7
days at 80ºF | | |
| | Accessory Materials | Airless
Spray Gun --
Phenolic Core Rollers
| | | | | | | |
|
| PFX-200 Petroleum - Marine Protective Coatings | | | PFX-200 is tough and flexible protective coating. It is a 60% solids Polyamide especially designed
for use in oilfield tanks or other vessels where chemical resistance is required. | Resistance
PFX-200 is highly resistant to acids, solvents, caustics, hydrocarbons, saltwater, and freshwater.
It was developed to withstand extreme corrosive and abrasive conditions with excellent outdoor durability. | Application Areas
PFX-200 is excellent as an anti-corrosive protective lining for floors, interior
and exterior of tanks, pipe lines, boat bottoms, swimming pools, aquariums, vats, etc. It retains a resilient
body, even after final cure. Can be used under constant spillage, immersion conditions, or highly abrasive applications.
It also works well as a brushing type adhesive. | Preparation
Surfaces should be free of rust, mill scale, oil, paint, films, grease, soluble salts, and other contaminants.
Sand blasting to white metal is necessary in most cases. Concrete should be etched to provide a profile for optimal
adhesion. Latinate and other loosely bound materials should be removed to provide a solid bonding surface. The
preparation procedures above are general guidelines. | Mixing
The mixing of parts A & B is very important! Material is supplied
in two containers as a unit. Always mix a complete unit in the proportion supplied. Agitate each
part separately before combining the two. PFX-200 has a mixing ratio of 1 to 1. 1 part “B” to 1 part
“A” (1:1). Use a jiffy mixer to thoroughly combine both parts and mix for 2 minutes. Use Lacquer
Thinner to thin PFX-200. Add no more than one quart of solvent per gallon of epoxy. In addition
to a thinner product, it also creates a longer pot life and easier workability. | Application
Apply
PFX-200 with a brush, 1/4" or 3/8” nap roller cover, or conventional spray equipment. Airless
spray equipment is preferred. Caution! Without the use of aggregate,
PFX-200 may be slippery when wet. | | Dry Film Application Rate | | To yield dry film of: | Apply
sq. ft. gallon | | 8
mls. | 200 sq. ft. | | 16 mls. | 100 sq. ft. | Heavy coats may be applied (up to 20 mils) without danger
of bubbling or pinholes in film. Several coats may be necessary in building up a heavy tank lining. Do not apply heavier than 20 mils per coat or sagging will occur. For heavier film, apply additional
coats. Additional coats must be applied as soon as the surface is tack
free or within 36 hours. |
| Clean Up
Application equipment should
be cleaned immediately with Lacquer Thinner. Use Apple Cider Vinegar to clean hands and skin. Do not allow PFX-200 to remain on tools! Once it sets and is cured, it is extremely difficult
to remove. | | Curing
Time | | Pot Life: | 12 hr. at 80ºF | | Drying Time: | 1 hrs. at 80ºF | | Complete: | 7 days at
80ºF |
| | Packaging | | 1 gal. units | | | 5 gal. units | | | 55 gal. units | |
| Color
PFX Standard Color (Gray, Red & White ) | Solids Contents
60% Solids | Mixing Ratio
1 part "B" to 1 part "A" (1:1) | Adhesion Resistance (ASTM D4060):
Taber
abraser CS-17 calibrase wheel at 4000 cycles with 1.5 mils wear and .30 grams lost. | Adhesion-Pull-Off
(D4541):
Concrete 100% substrate failure @ 1181 psi
Steel: 80% adhesive failure @ 2337 psi | | Impact Resistance
(D2794): 16 inch lbs. direct - passed | | Pencil Hardness (D3363): 6H - passed | | Compression (C579-96):
9,585 psi | Flammability:
Flammable during application. Will not support
combustion when cured. ____________________________________________________ |
| PFX-300 Floor - Pool & Basement Coating
| | | PFX-300 is a 75% solids epoxy resin polyamide
coating. It was especially designed and developed to withstand extreme conditions that will quickly destroy conventional
type protective paint coatings. | Typical Uses
PFX-300 is designed for adhering to
almost any clean surface, including aluminum, wood, metals of all types, plastic, brick, glass, concrete, and masonry.
PFX-300 has excellent anti-corrosion qualities and sward hardness. Recommended as an interior or exterior
coating. PFX-300 WILL NOT stick to Teflon, high-plasticized vinyl’s,
polyethylene, and silicone rubber. | Preparation
Surfaces should
be free of rust, mill scale, paint, algae, grease, oil, or any other film forming foreign material. Optimum
performance and adhesion is obtained if the surface is dry and a profile is created. Detailed preparation
methods are available through PermaFlex approved Training and Application Courses. | Mixing
The mixing of parts A & B is very important! Material
is supplied in two containers as a unit. Always mix a complete unit in the proportion supplied. Agitate
each part separately before combining the two. PFX-300 has a mixing ratio of 3 parts “B” to 1 part
“A” (3:1). Use a jiffy mixer to thoroughly combine both parts. Mix for at least
6 minutes and allow a 1/2 hour idle activation time before applying or adding thinner. This will also allow any
air bubbles to escape before application. Longer idle activation times (not to exceed ½ the pot life)
will produce quicker dry times. | Thinning
Thinning is generally not necessary when applying PFX-300.
Use as supplied if possible. If thinning is necessary, especially if spraying, thin no more than
2 quarts per gallon with Lacquer Thinner. Addition of thinner creates a longer pot life and increases possibility
of sag. | Application
Apply PFX-300 with brush, roller, or airless sprayer. Apply
at the rate of 1 gallon per 100 square feet in order to achieve 12 mils dried. Keep air pressure on spray equipment
as low as possible to minimize fogging. Vertical surfaces may require multiple coats to avoid sag. | | Dry Film Application Rate | | To yield dry film of: | Apply sq. ft. gallon | | 3 mls. | 400
sq. ft. | | 6 mls. | 200 sq. ft. | | 12 mls. | 100 sq. ft. | | |
| General
PFX-300 should be applied in well-ventilated areas. Surfaces should be free of foreign matter. DO NOT apply near open flame. | Clean Up
Application
equipment should be cleaned immediately with Lacquer Thinner. Use Apple Cider Vinegar to clean hands and skin.
Do not allow PFX-300 to remain on tools or in equipment! Once it sets and is cured,
it is difficult to remove. | | Curing Time | | Pot Life: | 6 to 8 hrs.
at 80ºF | | Drying Time: | 4 to 5 hrs. at 80ºF | | Complete: | 12 hrs. at 80ºF |
| | Packaging | | 1 gal. units | | | 1. 3 qts. of base | part "B" | | 2. 1 qt. of activator | part
"A" | | | | | 4gal. units | | | 1. 3
gals.gallons of base | part
"B" | | 2. 1 gal. of
activator | part "A" | Color
PFX Standard Color (Gray
and White) | Physical Contents
Solids - 75% by volume | Mixing Ratio
1
part "B" to 1 part "A" (3:1) | Adhesion-Pull-Off (D4541):
Steel: 1357
psi | Impact Resistance (D2794): 16 inch lbs. direct - passed ___________________________________________________ |
| Storage
& Handling | | *
| Upon receiving the product, all certified installers will ensure that products are labeled properly,
with batch number and lot. | *
| When storing
product ensure that it is not subjected to excessive heat or cold, moisture, or direct sunlight. For all other recommendations
as to storage refer to MSDS sheets. | *
| To
avoid any damage or contamination to product, handle as per manufacturers printed instructions. | *
| If damaged in shipping or storage, avoid using possible
contaminated product, remove from work site immediately. | *
| All MSDS sheets will be kept on hand for products being used on site with instructions
given to personnel on safety and health risks. _____________________________________________ |
|
| | | | | | | | | | |
|
|
